Ultra-low Power FSK Transceiver Module with AMICCOM A7149 RF Chip

Product Description

Ultra-low Power Consumption FSK Transceiver Module with Amiccom A7149 chip


Brief Introduction

DL-A7149-S was designed base on AMICCOM A7149 wireless transceiver chip. It is a compact and low power RF transceiver module. This AMICCOM A7149 is an ISM band wireless transceiver chip, mainly set to 433/868/915/MHz ISM/SRD frequency bands, with very low power consumption (e.g.: power consumption under 434MHz band in RX mode is just 1.8mA @ AGC Off).

Its link budget is very high, making it ideal for battery-powered long-distance wireless transmission applications. Its efficient Class E amplifier has an output power of up to 20dBm, a Max. sensitivity of -119dBm, and a Max. transmission rate of 250Kbps. By using this RF module, you can easily develop an excellent wireless product, with good RF performance and high reliability, without having a deep understanding of RF circuit design.


Features

● Compact size, SMD stamp edge half-hole encapsulation;

● Modulation method: FSK/GFSK;

● Working Voltage: 2.2~3.6V;

● Operating Frequency: 433MHz/868MHz/915MHz;

● Chip support speed range: 2-250Kbps;

● Low power consumption, receiving current 1.8mA (AGC Off);

● The maximum output power reaches 20dBm;

● High receiving sensitivity: -119dBm@2kbps;

● Independent 64BYTE transmit/receive data buffer;

● To reduce the power consumption, switching time between standby and receive state can be set  (WOR function);

● Supports RSSI signal strength detection.


Highlight Advantages:


Ultra-low Power Consumption (with only 1.8mA at full receiving state, best for battery powered applications)

At present, the power consumption of FSK transceiver chips in 433/868/915Mhz IoT applications is around 10mA, which cannot meet the requirements of most systems in industrial control and data acquisition industries, as most of them use battery power and require 3-5 years of use. But this DL-A7149-S RF module can achieve excellent power planning through software algorithm optimization, by optimizing the receiving working current to 1.8mA, extremely suitable for battery powered applications that require a long-life cycle, such as AMR (heat meters, gas meters, electricity meter, etc.), Remote Anti-theft Devices, Industrial Control, Smart Buildings, Energy Management, Smart Homes, Smart Security, Smart Agriculture, etc.


Wake on Radio (WOR): switching time between standby and receiving state can be set to reduce power consumption

By reducing the receiving state time of the receiver (while the rest of the time operates in deep sleep mode), the overall power consumption of the device can be reduced while ensuring its normal working.


Power Management:

Supports Deep Sleep Mode, Sleep, Idle Mode, and WOR Mode (Wake on Radio). The WOR function provides A7149 with automatic wake-up to receive RF network packets at irregular intervals. When it enters Deep Sleep Mode, it only consumes a current of 40nA. Overall, A7149 is a new generation of high-performance RF IC with extremely low receiving current and built-in +20dBm power amplifier, providing extremely long transmission range. The built-in power management function can greatly extend the battery life.


Other Advantages:

1. RSSI (Received Signal Strength Indication)

Built in RSSI can help you in detecting clean transmission channels, and the Auto Calibration mechanism inside the IC is used to overcome variations in semiconductor processes and work stably in various environments.


2. AFC (Automatic Frequency Compensation)

The function of Automatic Frequency Compensation (AFC) can solve the sensitivity degradation caused by RF frequency offset.

3. Ultra Long Range

Sub-1Ghz long-distance wireless module, can achieve 1KM communication range in an open space (without interference).

4. -120dBm High Receiving Sensitivity

High receiving sensitivity -120dBm@2Kbps, IFBW:50khz

5. Ultra Compact Size

Ultra small packaging surface mount design: 12.5*12mm (only half the size of a coin).


Applications

● ISM band data communication ;

● Smart Building;

● Smart Home System ;

● Intelligent Security Monitoring ;

● AMR (Automatic Mobile Robot) ;

● Wireless Remote Control;

● Wireless Sensor Networking ;

● Energy Control and Management ;

● RKE (Remote Keyless Entry) ;

● Heat energy collection, meter measurement ;


Download Center

DL-A7149-S FSK Wireless Transceiver Module - V1.0.pdf  


Technical Parameter

Parameter

Min.

Typical

Max.

Unit

Remarks

Operating Conditions

Working Voltage (VDD)

2.2

3.3

3.6

V

To ensure maximum chip power, stable voltage should ≥3.1V

Communication Level Range

-0.3

3.3

3.6

V

Exceeding this range will damage the chip

Working Temperature Range

-40

25

85

The larger the temperature difference, the greater the bandwidth is required for communication

Current Consumption

Receiving Current

1.8

2.2

3.8

mA

@DCDC

WOR working mode can be used to reduce the overall working current

Transmission Current

97

117

137

mA

@433MHz: 19dBm, DCDC 50Ω

78

98

118

mA

@868MHz/915MHz: 17dBm, DCDC 50Ω

Sleep Current

0.2

0.5

1

uA

Save via register

RF Parameters

Transmit Power Range

-30

19

20

dBm

Software configurable

Receiving Sensitivity


-119

-117

-115


dBm

@433MHz,2Kbps, IFBW:50KHz

@868MHz,2Kbps, IFBW:50KHz

@915MHz,2Kbps, IFBW:50KHz

Communication Rate Range

2


100

Kb/s

@Different crystals result in varying rates, Max. up to 250K


Pins Definition

No

Definitions

Type

Description

1

ANT/NC

AI/AO

RF signal input/output port, π-matching circuit must be reserved; Adopt 50Ω impedance matching for RF routing, route the ground and add via holes around it

2

GND

PWR

Reliable grounding

3

3.3V

PWR

To ensure maximum chip performance, a stable voltage (≥3.1V) is required

4

GPIO2

O

Function can be configured through the SPI interface

5

GIO1

O

Function can be configured through the SPI interface

6

SDIO

IO

SPI data input/outpu

7

SCK

I

SPI Serial Clock Input, connected to the SCLK of MCU

8

SCS

I

SPI Chip Select Input, connected to the CSN of MCU

9

GND

PWR

Reliable grounding

10

NC

NA

No connection

11

NC

NA

No connection

12

PDNHA

I

DC-DC PWM mode control, high level for sleeping

13

NC

NA

No connection

14

RST

I

Hardware reset to increase its stability,

chip initialization, low-level reset

15

CKO

O

SPI Serial Clock output, no connection is needed

16

GND

PWR

Reliable grounding


Size

DreamLNK is a high-tech enterprise specializing in ISM band micropower wireless communication technology, providing different kinds of wireless modules and one-stop IoT solutions, including 433/868/915MHz wireless modules, 2.4G RF Modules, FSK Transceiver Modules, Antennas, Remote Controls, and customized wireless RF solutions. Welcome to inquire!

UART Wireless FSK Transceiver Module Base on CMT2310 RF Chip

SX1278 High Power Wireless LoRa Module with PA & LNA (433/470Mhz)

Wireless LoRa Module 433Mhz/868Mhz/915Mhz High Sensitivity (-129dBm) LLCC68

915MHz RF Transceiver Module with -120dBm Sensitivity and 1.8KM Range

RFM69HC 433/868/915Mhz Wireless Transceiver Module with SX1231 Chip