433Mhz Wireless Transparent SoC Transceiver Module TI CC1310 Chip

Product Description

433MHz Wireless Transparent SoC Transceiver Module with TI CC1310 Chip


Brief Introduction

DL-CC1310-B Wireless Module is a SoC embedded Serial Port RF Transceiver Module (UART Module) with AT command, which was developed by DREAMLNK based on TI' CC1310 (built-in dual-core ARM) Radio Frequency chip. It combines an integrated RF Controller (Cortex®-MO) and a powerful Arm® Cortex®-M3 Processor, the Clock Speed of the MCU can reach up to 48MHz.

This DL-CC1310-B Wireless Module supports Narrow-band Communication, Direct Sequence Spread Spectrum (DSSS), Long-range Transmission and High-efficiency Communication. It has built-in fully functional AT Commands that support any Serial Baud Rate setting from 1920bps to 256000bps, which can greatly improve the communication efficiency with up to -124dBm receiver sensitivity.

The embedded software makes this Wireless Module support not only Transparent Transmission Mode, Accurate Signal Strength Indication, automatic CCA (Clear Channel Assessment), but also High-speed Data Stream & Packet Segmentation Transmission, which can effectively reduce the probability of signal collision.


Hardware Features:

● Original CC1310 Chip from TI;

● SOC integrated RF module with metal shield

● Industrial grade components: 433/868/915MHz

● Wide supply voltage range: 1.8V to 3.8V;

● Ultra-low sleep current < 1uA;

● High efficiency receiving performance (RX current @ 5.5mA);

● High Transmission Efficiency:

TX (+10dBm): 17mA;

TX (+14dbm): 27mA;

● Excellent Receiver Sensitivity:

Long Range Mode: -124dbm at 0.625kbps;

Universal Mode: -110dbm at 50kbps;

● Accurate Signal Strength Indication and Clear Channel Assessment (CCA).

● Compact size for SMD mounting (Dimensions = 18x16.5mm)


Software Features:

● Easily configure with defaulted AT command, for a simple development;

● Transparent Transmission Mode supported;

● Data flow control & high-speed data stream transmission supported;

● 1920-256000bps serial baud rate is supported;

● 0.6kbps-500kbps wireless baud rate is supported;

● Wake-on-Radio (eWOR) function supported, which can be greatly increases the battery standby time;

● Packet Segmentation Supported

● Preset CCA (Clear Channel Assessment) function, which can effectively reduce the collision probability of co-frequency interference;

● Strong Anti-jamming: supports anytime RSSI acquisition and CCA (Clear Channel Assessment);

● Supports manual fast frequency hopping to avoid co-frequency interference;

● Point-to-Point, Broadcasting and Monitoring transmission can be achieved.

● Remark: there are three versions available

  - DL-CC1310-B-868  868MHz Transparent UART Module:  Frequency @ 868MHz

  - DL-CC1310-B-915  915MHz Transparent UART Module:  Frequency @ 915MHz

  - DL-CC1310-B-433  433Mhz Transparent UART Module:  Frequency @ 433MHz

Download Center

DL-CC1310-B Specification V1.12 


Technical Parameter

Parameter

Min.

Typical

Max.

Unit

Remarks

Operating Conditions

Working Voltage

2.0

3.3

3.6

V

Voltage above range may damage the RF module

I/O Voltage Range

1.8

3.3

3.6

V

Recommended Operating voltage is +3.3V

Working Temperature Range

-40

25

85


Current Consumption

Receiving Current

5

5.5

6.1

mA

@ Radio Frequency Receiving Current (MCU sleep)

Receiver Working Current

6

6.8

8

mA

@ Overall Receiving Current

Transmission Current

32

25

15

35

27

17

38

29

20

mA

@433M 15dBm Peak value

@433M 14dBm Peak value

@433M 10dBm Peak value

27

16

29

18

32

21

mA

@868M 14dBm Peak value

@868M 10dBm Peak value

27

16

29

18

32

21

mA

@915M 14dBm Peak value

@915M 10dBm Peak value

Standby Current

1

1.5

2

mA

@ Radio Frequency Receive Function Stopped

Sleep Current

0.2

<1

2

uA

@M1=0

RF Parameters

Recommended Frequency (Ensure best performance))

420

433

510

MHz

@433Mh RF module

840

868

915

930

MHz

@868Mhz/915Mhz RF module

Transmitting Power Range

-10

14

15

dBm

@0-10dBm, 1dbm resolution

Max. Receiver Sensitivity @ FSK

-120

-124

-127

dBm

@868Mhz/915Mhz

@625bps

-119

-122

-124

dBm

@433Mhz

@625bps

FSK Rate Range

0.625

9.6

500

Kbps

@ See Recommended Configuration for details

Wake-on-Radio Mode Consumption


0.04


mAH

@AT+RXGAS=500


Recommended Configuration


Rate (bps)

Focus on

Clear Channel Threshold Setting

Recommended Channel Spacing

WOR Function

625

Range optimization

-92 dBm

250Khz

Not Available

1250

Range optimization

-92 dBm

250Khz

Not Available

3750

Range optimization

-92 dBm

250Khz

Not Available

2500

Range optimization

-92 dBm

250Khz

Not Available

5000

Range optimization

-92 dBm

250Khz

Not Available

2400

Common mode

-92 dBm

250Khz

Available

3600

Common mode

-90 dBm

250Khz

Available

6200

Common mode

-90 dBm

250Khz

Available

9600

Common mode

-90 dBm

500Khz

Available

14400

Common mode

-85 dBm

500Khz

Available

19200

Common mode

-85 dBm

500Khz

Available

25000

Common mode

-85 dBm

500Khz

Available

38400

Common mode

-85 dBm

500Khz

Available

50000

Common mode

-80 dBm

500Khz

Available

70000

Common mode

-80 dBm

500Khz

Not recommended

100000

Common mode

-80 dBm

500Khz

Not recommended

200000

Common mode

-75 dBm

1Mhz

Not recommended

300000

Common mode

-75 dBm

1Mhz

Not recommended

400000

Common mode

-75 dBm

1Mhz

Not recommended

500000

Common mode

-75 dBm

1Mhz

Not recommended


Module Size

Pin Definitions


Pin Name

I/O Type

Pin Description

VCC

PWR

To maximize the chip function, ≥2.5V stable voltage is recommended

GND

PWR

Reference Ground

ANT

Analog I/O

RF signal input/output port, π-matching network must be reserved;

Adopt 50Ω impedance matching for RF routing, route the ground and add via holes around it

DIO1(AUX)

Out

Indicate the working status of the module:

Start-up initialization or wake-up mode initialization:

0: Initialization completed; serial port transmission can be carried out

1: Serial port transmission is not allowed until initialization is completed

AT Command:

0: Idle

1: TX buffer is full and needs to wait for low level before transmission

Transparent Transmission Mode & Wake-on-Radio (WOR) Mode:

0: Idle

1: The module receives the data and outputs the data through the serial port after the set delay

When Transmitting Data to the Module:

0: The buffer is empty (Transmitting completed) / the buffer is not full

1: Buffer is not empty / buffer full,

(Two settings can be configured by “AT+ AUXM” Command)

DIO2(UART-RX)

In

TTL serial port input, connected to external TXD output pin

DIO3(UART-TX)

Out

TTL serial port output, connected to external RXD input pin

DIO4(M0)

In

Switching between AT Command and Transparent Transmission Mode, defaulted high level

0: Transparent Transmission Mode

1: AT Command Mode

DIO5(M1)

In

Control Module Sleep, defaulted high level

0: Sleep (or wake-on-radio)

1: Wake up

DIO6-DIO14

Out / In

Common I/O port, no function at present, can be customized to realize the following functions:

1. ADC detection

2. Key value fast transmit

3. RF status indication

4. PA control

If not used, it must be N/C (No Connection)


Typical Application

Wireless Data Communication, Wireless Data Monitoring and Transmission, Wireless Voice/Audio Transmission, Wireless Sensoring; Wireless Remote Control System; Wireless Game Controller, Remote Control Toys; Wireless remote control for electronic consumer products; Wireless Alarm & Security Control System; Wireless Sensor Networking, Automatic Data Collection; Industrial Remote Control, Intelligent Control System, Home Automation, Home Appliance Control, Building and Residential (smart home) Control, Smart City, RFID (radio frequency identification); Telemetry, Automatic (Water, Electricity, Gas) Meter Reading system; Remote control that supports radio frequency (RF) technology


Product Tags

UART Serial Module, Radio Transmitter Module, RF modules, RF Transmitter, RF Transmit module, Wireless Transmitter Module, ASK Transmit Module, RF Transmitter Module, Wireless Module

UART Wireless FSK Transceiver Module Base on CMT2310 RF Chip

BLE 5.3 Bluetooth Module with TI's SimpleLink™ CC2340R5 Chip

433Mhz UART Wireless Transceiver Module with PAN3028 Chip

433Mhz High Power UART Wireless Transceiver Module with PAN3028 Chip

868MHz/915MHz Transparent UART Transceiver Module with TI CC1310 Chip